Protected: Tim Hornyak

Forum Replies Created

Viewing 14 reply threads
1 2
  • Author
    Posts
    • December 7, 2021 at 22:04 #16609
      Tim Hornyak
      Participant

      Almost 4 years later and still getting same results for my engine pre- heating. Works well and simple to use. Added a picture of the unit.

      Attachments:
      You must be logged in to view attached files.
    • November 22, 2021 at 20:46 #16529
      Tim Hornyak
      Participant

      Just build an AA1 profile in Foreflight from the data in your owners manual. That’s what I did , accurate to within .3-.5 gallons/ 2-3 mins during a 2.5 hr flight. Fairly basic data but it works well.

    • November 14, 2021 at 15:36 #16491
      Tim Hornyak
      Participant

      Is this what you’re looking for?

      Attachments:
      You must be logged in to view attached files.
    • July 1, 2021 at 19:44 #15995
      Tim Hornyak
      Participant

      Couple things I’d check; The thumb screw that holds canopy open make sure it is fully loosened, take off the glare shield or crawl under the panel and see if the canopy rail is hitting insulation/wiring/etc. Also you’re missing the windshield bow seal , that will close the gap about 1/4 inch or so.

    • June 17, 2021 at 11:20 #15955
      Tim Hornyak
      Participant

      One more

      Attachments:
      You must be logged in to view attached files.
    • January 28, 2021 at 06:46 #15232
      Tim Hornyak
      Participant

      It is a metal overlay, it was installed prior to me buying so not sure where the decals came from but any graphics shop should be able to do them.

    • August 10, 2020 at 20:11 #14496
      Tim Hornyak
      Participant

      I have a set on my Yankee, they look great and are high quality.

    • April 28, 2020 at 14:54 #13731
      Tim Hornyak
      Participant

      Here’s a picture of the old vs new lens.

      Attachments:
      You must be logged in to view attached files.
    • December 22, 2019 at 19:11 #13095
      Tim Hornyak
      Participant

      According to the installation manual the gps input will be VFR only, without approach capability ( no glide slope), hopefully that changes w the certified version.

    • December 13, 2019 at 13:48 #13074
      Tim Hornyak
      Participant

      I have the C1 w Nav steering installed on my AA1 and have the operation manual but not the installation manual. Works great!

    • July 21, 2019 at 13:16 #12628
      Tim Hornyak
      Participant

      Parts

    • July 21, 2019 at 13:04 #12624
      Tim Hornyak
      Participant

      Additional

    • July 21, 2019 at 13:03 #12622
      Tim Hornyak
      Participant

      Additional pictures

      Attachments:
      You must be logged in to view attached files.
    • January 24, 2019 at 07:26 #12171
      Tim Hornyak
      Participant

      I’m on the waiting list as well. I watched a friend install one on a RV8. Under 10 mins to install and 5 mins to configure. It is literally two screws, pos/neg wires and a iPhone app to configure. You can download the template w the dimensions, the two screws line up perfectly on AA1.

      • This reply was modified 5 years, 5 months ago by Tim Hornyak.
    • October 12, 2018 at 19:21 #9584
      Tim Hornyak
      Participant

      There has been some discussion on GG and GPA about rigging control surfaces on our aircraft. Here is the benefit of a properly rigged airplane; flying hands off at the top of the Green Arc with a lot of throttle remaining.

      Attachments:
      You must be logged in to view attached files.
  • Author
    Posts
Viewing 14 reply threads
1 2